Xhorse Condor XC-MINI Cutting Calibration Steps

ikeycutter condor xc mini Key Cutting Machine which is with Built-in database, can easily find key information.Xhorse MINI Condor is on promotion with 2999USD free shipping,with enough stock now.Here Xhorse VVDI shares Cutting Calibration guide.

Xhorse Condor XC MINI Cutting Calibration Steps

1.Enter the Main interface, Click on Self Test

2.Enter Self Test interface, Click on Cutting Calibration

3.Follow the steps on the screen, then click on CONTINUE, The Cutting Calibration in Process

4.Please use the brush to clean up the clamp cutting spot, the probe and the cutter. then click on CONTINUE, Cutter Calibration Complete

www.xhorsevvdi.com all rights reserved, Original Article url:Xhorse Condor XC-MINI Cutting Calibration Steps

How to use Benz ECU Test Adaptor with VVDI MB for ME9.7, ISM and 722.9 ETC board

VVDI MB BGA Tool with Benz Ecu Test Cables  is OK to renew ME9.7 MB, ISM in w164 and w221 and used 722.9 ETC board (7-gearbox module) version VGS_73 or like as 3.

1.ME9.7 ECU Renew Steps

VVDI MB connection.

Read data

Get erase pass

Save data(backup)

Renew – success

Now you can initial startup in DAS/Xentry, have there 2 possibility…with data from old ECU or without… then online

FOR get erase pass ONLINE WITH DEVICE VVDI MB Tool, After reading data ECU (with vvdi mb)

pin connection for ME9.7 MB

Finally, ECU renewed, and put into car made adaptation works good. Car starts.

Benz ECU renew cable can renew (used) ISM in w164 and w221, when is the ISM unit in 100% condition and not broken.
Successfully renewed used 722.9 ETC board (7-gearbox module) version VGS_73 or like as 3 with VVDI MB tool and today assigned to the car using MB-SCN online access.

www.xhorsevvdi.com all rights reserved, Original Article url:How to use Benz ECU Test Adaptor with VVDI MB for ME9.7, ISM and 722.9 ETC board

How to use Condor XC-MINI Cut GM DWO4 B114R Key with M1 Clamp?

Xhorse Condor XC Mini Master can cut key by several different way,and here we will display Cutting by Bitting way with DWO4 key GM B114R detailed instruction.

1.Start Condor XC-MINI Key Cutting Machine,and click “Cutting by Bitting”on the screen.

2.Enter with “DWO4”

3.Then the screen will display which clamp needs to work with.Please use the M1 clamp,put the located block into M1 clamp shoulder groove position.

4.Tighten the M1 clamp.

5.Put the original DWO4 key. Let the aligh on the key shoulder position by using the located block.

6.Tighten the original key,and remove located block.

7.Click “Key Code”on menu.Then confirm.

8.Put the located block into M1 clamp shoulder groove position again,then put the DWO4 blank key blade on clamp.

9.Click “Correcting & Cut”,then cutting in process.

10.End.

www.xhorsevvdi.com all rights reserved, Original Article url:How to use Condor XC-MINI Cut GM DWO4 B114R Key with M1 Clamp?

Xhorse Condor XC-MINI,Condor XC-002,XC007 Key Cutting Comparison

Condor XC-MINI Key Machine,Condor XC-002,XC007 Key Cutting Machine are original Xhorse key cutting tool,and XC-007 stop producing any more.Condor XC-002 Manually Key Cutting and XC-MINI which can replace full of XC-007 key cutting machine,both of them are available.

1.Condor key cutting machine Specification Comparsion:

Key cutting machine	Condor XC-007	Condor XC-MINI	Condor XC-002
Input Voltage	AC110V/220V	90V–264VAC	220VAC
Input Frequency	47~63Hz	47~63Hz	50Hz
Consume	220W	200W	200W
Packing Dimensions	L460*W 520*H 620mm	L450*W450*H350mm	L595*W550*H375mm
Machine Dimensions	L336*W 407*H490mm	L265*W362*H301mm	L298*W445*H525mm
Display	800*480	1024*600
Spindle Speeds	12,000 rpm	9000rpm	8000-10000rpm
USB	USB2.0	USB2.0
Working Temperature	0~50℃	0~50℃	0~50℃
Humidity	10~90%	10~90%	10~90%
Net Weight	31Kg	18Kg	23Kg
Gross Weight	35Kg	22.9Kg	28Kg

2.Xhorse iKeycutter Condor machines Differences::

Condor XC MINI master is the mini version of Condor XC-007 machine,can replace XC-007.And both of them are automatic key cutting tool.

But the new Condor XC-002 is a manual/mechanical key cutting machine.

XC MINI has no limitation in applied voltage, while XC-007 needs setting, use with 220V voltage

Weight: condor xc-007 master series > condor xc-002 > mini condor (lightest)

3.Condor MINI and Condor XC-002 Manually Features Difference

Condor XC Mini Master:

1. Built-in Database
2. Support Mulit-languages
3. 7” Capacitive Touch Screen
4. 3-Axis Precision Ball Screw Transmission
5. Cross Rail
6. All Aluminum Machine Body
7. Single machine with both Tracer/Cutter
8. Standardly include 2 clamps M1/M2
9. Software supports online-update
10. Support Sided/Track/Dimple/Tibbe keys
11. Some Dimple/Tibbe keys need optional clamps

Condor XC-002 Manually:

Aluminum Die-casting chassis

Precision Machining

Renishaw line detection system

Column Cross guide rail

1 year warranty. Lifelong technical support

www.xhorsevvdi.com all rights reserved, Original Article url:Xhorse Condor XC-MINI,Condor XC-002,XC007 Key Cutting Comparison

How to use Condor XC-MINI Cut Toyota TOY48 Key with M2 Clamp

Xhorse Condor XC MINI can cut key with database,or cutting by bitting,fid bitting.Here Toy48 cutting key is also by key databse,we will display the detailed steps about ikeycutter condor xc mini Key Cutting Machine Toyota TOY48 cutting process.

1.Click “Key Database” on the screen.

2.Enter “Toyota” ,click on “confirm”.

3.Enter key code “46422”,then confirm.

4.Put the M2 clamp and tighten it.

5.Put the new key blade “TOY48”.

6.Click “Cut”.And then turn to oppsite side to cut.

7.Complete.

www.xhorsevvdi.com all rights reserved, Original Article url:How to use Condor XC-MINI Cut Toyota TOY48 Key with M2 Clamp

How to use Condor XC-MINI Cut Suzuki HU87R key by Bitting Way

Condor XC-MINI key cutting machine support large arrange of car brands.Here Xhorse VVDI will dispaly cut by bitting way to cut SUZUKI HU87R key.

1.Start your Condor XC-MINI,and click “Cut by Bitting”on the main menu.

2.Choose HU87R in the list.Then click confirm.

3.Input the key bittings.

4.Put the key and tighten it.

5.Then start to cut.

6.Finish.

www.xhorsevvdi.com all rights reserved, Original Article url:How to use Condor XC-MINI Cut Suzuki HU87R key by Bitting Way

How to Find Bitting With Condor XC-MINI Key Cutting Machine?

Condor XC-MINI Key Cutting machine support cut by key cutting way,key database,key duplication.When use condor xc-mini key cutting tool to cut keys,sometimes needs to input key bittings.Here we will dispaly how to use “find bitting”.

Parts of the car are missing bitting on door lock/trunk lock/ignition lock, enter unknown bitting as “?”

1.Enter the Main interface, Click on Find Bitting

2.Select Car Maker and then Click on Confirm

3.Select the Blank Key. Click on Confirm.

4.Select Key Type.Click on Confirm.

5. Enter known bitting. Enter unknown bitting as “?”. Click on Find Bitting Code.

6.Possible key bitting will be listed. Note that system has sorted the codes by the most economical way in order to save blank keys. For example, the bitting under ” First key” only needs three blank keys, the bitting under “Second Key” need another three blank keys, then the “third Key”.

www.xhorsevvdi.com all rights reserved, Original Article url:How to Find Bitting With Condor XC-MINI Key Cutting Machine?

Choose which one to program Mercedes key VVDI MB Tool or AVDI?

This blog is going to answer a question: Choose VVDI MB Tool or AVDI to program Mercedes keys? Below are some reviews to help you make a right choice!

Story is that a guy wants a tool to program Mercedes keys and deal with ELV/ESL problems, but hesitate to choose VVDI or AVDI. Then people start arguing.

The final conclusion:

For Mercedes key/ELV/ESL, Xhorse VVDI MB BGA TOOL is better choice than AVDI.

VVDI is much cheaper than AVDI and VVDI is even better in some areas!

VVDI MB Tool price: $1779 free shipping.

VVDI is better than AVDI in below areas:

1. VVDI can write/erase cheap BE keys – AVDI no
2. VVDI can repair fatal error on ESL 204 – AVDI no
3. VVDI can read password from key V51 – AVDI no
4. VVDI can renew key V51 without damaging radio bytes – AVDI no

Some people said VVDI need tokens but AVDI doesn’t need?

Yes, it’s true. But VVDI needs tokens only for online key calculations. And you need to do online calculation only when EZS with NEC and BGA key.

VVDI MB Tool Function Introduction:

Support BE keys, read password and prepare new key via IR

NEC V051, V057 support on board get password

All NEC keys support on board write and erase

Password calculate work fast: support BGA keys, NEC keys (include 51, 57version)

Support to renew and write EIS/ ELV

Support online generate key file

Unlock ELV function will be released soon

More information you can check here:

http://www.xhorsevvdi.com/wholesale/xhorse-vvdi-benz-vvdi-mb-bga-tool.html

www.xhorsevvdi.com all rights reserved, Original Article url:Choose which one to program Mercedes key VVDI MB Tool or AVDI?

Free Download V4.5.6 VVDI Prog Software (2017.03.21 Update)

V4.5.6 VVDI PROG Programmer newest software is released on Mar 21th.Here is the vvdi prog programmer software newest download link.

1.Free Download V4.5.6 VVDI Prog Software

Here is the download link:https://mega.nz/#!jpoEhToS!m9NoYIAhLhjLX-8imfQng7IQgwcGvVWFwxb7W_VlAL8

2. V4.5.6 VVDI Prog Update Informaiton

VVDI Prog v4.5.6 (2017-03-21)

* This version DON't need update firmware

* Fix some bugs

+ Add VVDI PROG USER MUNUAL 4.5.6 version in Doc folder

+ Support operate software while opening the diagram

* Fix MC9S12G192,MC9S12GA19,MC9S12G240,MC9S12GA240 options PFLASH write error problem

+ Add PIC12F635,PIC12F683 options in <2-MCU>-><MICROCHIP-PIC12F>

+ Add PIC16F631,PIC16F636,PIC16F639,PIC16F677,PIC16F684,PIC16F685,PIC16F687,PIC16F688,PIC16F689,PIC16F690 options in <2-MCU>-><MICROCHIP-PIC16F>

+ Add JIEFANG-J6-BCM option in <4-IMMOBILIZER>-><FAW> (Need to use with VVDI2)

+ Add FC-OPERATION-UNIT-W221 option in <8-OTHER>-><BENZ>

This is from original xhorse vvdi official site:Free Download V4.5.6 VVDI Prog Software (2017.03.21 Update)

How to program Mercedes W221 BGA BE key by VVDI MB Tool?

This is a tutorial to guide you: How use Xhorse VVDI MB Tool to program Mercedes BGA BE key for W221? Steps are as below:

First connect VVDI MB BGA Tool with car via OBD2 port.

Part 1: VVDI MB Tool calculate W221 BGA key password

Open VVDI MB Tool software, go to “Password Calculation”, select chassis “W221” then click “Data Acquisition”.

Follow the tips:

Insert a working key into ignition and wait 5 seconds→ take it out then insert it again→ insert it into the VVDI MB IR reader (the coil).

Data Acquisition is performing.

Insert the working key into ignition and wait 30 seconds.

Insert it into IR reader and wait the message show “Reading data success”.

After that, save the file, Data Acquisition finish!

Then click “Upload Data” and choose the file to open.

After upload success, click “Query Result” and click “OK” to continue.

Sometimes you must generate up to 6 files to get the password.

VVDI MB Tool successfully calculate W221 BGA key password!

Part 2: VVDI MB Tool program Benz W221 BGA key

Copy the password and go to “EIS Tools”, click “Read EIS data”.

Click “Paste” to paste key password.

Click “Save EIS data” to save the EIS bin file.

Next go to “Prepare Key File” and click “Load EIS file”.

Choose the bin file to open.

Then select key position for key file and key file format.

Uncheck the boxes “V041” and “V011”.

After that, go to “Read Write Key” and put the new key into IR reader.

Choose type as “BE key” and click “Load key file”.

Then click “Write”.

Wait the message show “Write data success”.

Xhorse VVDI MB Tool successfully program Benz W221 BGA key!

Key is working!

This is from original xhorse vvdi official site:How to program Mercedes W221 BGA BE key by VVDI MB Tool?

How to solve VVDI MB BGA "Erase EIS Failed" Error?

Xhorse ELV Emulator for Benz 204 207 212 Work with VVDI MB BGA Tool.Erase EIS, then re-write EIS and personalize ESL, finally ESL is synchronized.

And when install W204 ELV Emulator with VVDI MB BGA Tool,after click "Renew EIS",got the error "Erase EIS ......Failed",like the following pic:

And check the detailed video from customer,find the after click "Get" for the erase password,then copy the erase password in the key password.The Key password and erase password are not same.Please get your key password,then it will be OK.

If you key is V51,V57 version,you can use VVDI MB with NEC Key Adaptor to read key password directly.If not,you can use password calculation to get,but it will need the vvdi mb token.

1.How to add W204 ELV Emulator with VVDI MB BGA Tool:

1.Connect EIS,Xhorse ELV Emulator.

 

2.Start VVDI MB Tool Software.

 

3.Clikc ESL Tool,choose chasis,and OBD way,then press Read ESL Data.
4.After read esl data,tick off Personalized and Activated option.
5.Click “EIS Tools” on the left,choose OBD way,and Chasis type to read EIS Data.
6.Click Get to erase EIS key password.
7.Paste key password,then save EIS data.
8.Press OK to save HC05 format file.
9.”EIS Tools” page,choose IR mode,and click “Renew EIS”,then insert IR key to EIS.
10.Insert IR adapter to car. Take out and insert again if it is already inserted. Wait about 28 seconds until erasing EIS success
11.Select OBD mode,click “Read EIS data”.Reading data success, EIS is normal.
12.Click Load EIS data,and please open EIS data saved previously.
13.Click Write VIN.Please confirm VIN and click Yes to continue.
14.After write VIN success.Choose IR model,select Write EIS data,then click YES
15.Please wait until Writing data success.Select OBD mode,and click Personalize W204 ESL.
16.ELV is personalized.

2.VVDI MB with NEC Key Adaptor to read key password Steps:http://blog.xhorsevvdi.com/how-to-use-vvdi-mb-bga-to-read-benz-v57-key-password/

This is from original xhorse vvdi official site:How to solve VVDI MB BGA "Erase EIS Failed" Error?